www.tarpcentral.com Toggle Search Account Checkout Cart SUPPORT Blog Contact Us Dealer Portal Employment Installation Instructions Meet the team! Fas-Top FAQs ROLL TARP SYSTEMS Features ELECTRIC TARP CONVERSION KITS Grain Trailers Install Instructions for Electric Tarp Conversion ELECTRIC HOPPER OPENER KITS Install Instructions for Dura-Trap Electric Hopper Opener TARPS & PARTS Electric Tarp System Parts Equipment Transport Windshield Protectors Fitted Grain Drill Seeder Covers Roll Tarp System Parts Search site Submit search Nav Menu 2 Nav Menu 3 Nav Menu 4 Nav Menu 5 Nav Menu 6 Nav Menu 7 Nav Menu 8 > ELECTRIC TARP CONVERSION KITS > Install Instructions for Electric Tarp Conversion ...New Gallery 2019/6/6STEP 1Measure for placement of the front base on the trailer, approximately 31’’ down from the top of the trailer. NOTE: Not from the roll tarp end cap.originaldate 1/1/0001 6:00:00 AMwidth 444height 251STEP 3Using a 5/16’’ drill bit, drill out the marked rivets/holes.originaldate 1/1/0001 6:00:00 AMwidth 441height 247STEP 4Thread holes with the provided 3/8’’ self threading bolt.originaldate 1/1/0001 6:00:00 AMwidth 441height 248STEP 5 Using 1 1/4’’ x 3/8’’ bolts , mount the base utilizing the pre-threaded holes.originaldate 1/1/0001 6:00:00 AMwidth 439height 246NOTEFor trailers with ribbed paneling, it is necessary to use nylon spacers provid- ed.originaldate 1/1/0001 6:00:00 AMwidth 439height 249STEP 6On the interior of trailer install the 3/8’’ nuts, lock washers, & flat washers onto the 1 1/4’’ x 3/8’’ bolts.originaldate 1/1/0001 6:00:00 AMwidth 438height 249STEP 2Position the base with the top hole at the 31’’ mark down from the top of the trailer. Have the center line decal on the center stake of trailer and mark the remaining rivets/ holes. NOTE: If the catwalk is in the way deter- mine if above or below the catwalk is closer to 31’’.originaldate 1/1/0001 6:00:00 AMwidth 434height 243STEP 8Drill a 1’’ hole below the base, preferrably under catwalk so cables do not touch.originaldate 1/1/0001 6:00:00 AMwidth 438height 246STEP 9Install small rubber grommet in the 1’’ hole.originaldate 1/1/0001 6:00:00 AMwidth 440height 247STEP 11Determine desired location for the plug receiver. Before drilling 2’’ hole check to make sure there are no wires or hoses underneath or in the way.originaldate 1/1/0001 6:00:00 AMwidth 440height 247STEP 12Install receiver using 3/8’’ self threading bolts.originaldate 1/1/0001 6:00:00 AMwidth 425height 244STEP 13Mount rear base in a similar manner as the front base.originaldate 1/1/0001 6:00:00 AMwidth 430height 242STEP 14Use the holes on the face of the base that is closest to 33’’ down from top of trailer to mount the pivot/arm assembly with the 1 1/4’’ x 1/2’’ bolts provided.originaldate 1/1/0001 6:00:00 AMwidth 425height 240STEP 17Pull the end of the roll tube out away from the tarp and insert roll tube adapter, spot weld straight then weld. Be sure to protect the tarp and surrounding objects from welding splatter. Let the weld cool , then slide the roll tube back into the white poly bushing of the rear arm (approx. 2-3’’ beyond bushing).originaldate 1/1/0001 6:00:00 AMwidth 438height 248STEP 18 Mount the motor to the front arm, using the 5/16’’ nuts and lock washers.originaldate 1/1/0001 6:00:00 AMwidth 439height 246STEP 19 Install cable terminals to the studs on the motor. Do not allow stud to spin when tightening, and do not over tighten.originaldate 1/1/0001 6:00:00 AMwidth 438height 245STEP 20Install motor to motor shaft adapter with the 1 3/4’’ x 3/8’’ bolt and 3/8’’ locking nut.originaldate 1/1/0001 6:00:00 AMwidth 439height 245STEP 21Mount the retaining washer to secure motor.originaldate 1/1/0001 6:00:00 AMwidth 440height 248STEP 22Install motor cover using 1/4’’ torque screws and lock washers provided.originaldate 1/1/0001 6:00:00 AMwidth 438height 244STEP 23To reinstall the u-clamps, be sure the roll tube is slid back into rear arm then square front arm with the face of the trailer. Next, install front u-clamp and remove all wrinkles and twists from pock- et by stretching the tarp from the back of trailer. Proceed installing the rest of the u-clamps.originaldate 1/1/0001 6:00:00 AMwidth 438height 246STEP 24Square rear arm with the back face of the trailer. Then install roll tube collars.originaldate 1/1/0001 6:00:00 AMwidth 437height 246Front of trailer.originaldate 1/1/0001 6:00:00 AMwidth 365height 267Back of traileroriginaldate 1/1/0001 6:00:00 AMwidth 394height 250originaldate 1/1/0001 6:00:00 AMwidth 2226height 1248STEP 10Lace cable through arm as shown and push through grommet, let cable sag down a few inches from the catwalk.originaldate 1/1/0001 6:00:00 AMwidth 437height 244STEP 15Remove bungee cord and u-clamps from tarp.originaldate 1/1/0001 6:00:00 AMwidth 615height 342STEP 16Meaure from front arm to 3’’ beyond rear arm to determine length of roll tube and adapter.originaldate 1/1/0001 6:00:00 AMwidth 192height 127 Sort By: Price: Low to High Price: High to Low Most Popular Title Manufacturer Newest Oldest Availability 30 per page 60 per page 120 per page 180 per page 300 per page Page of 1 1.8 Hp Motor With Gear Box Price: $699.00
